SUNSETTER EASYSHADE INSTALLATION INSTRUCTIONS
WARNING: PLEASE MAKE SURE TO CALL TECHNICAL SUPPORT IF YOU HAVE ANY
QUESTIONS AT ANY POINT. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT
IN PERSONAL INJURY!
PLEASE CALL TOLL FREE 1-800-670-7071 FOR TECHNICAL SUPPORT
Tools Needed:
Electric Drill
1/8" Drill Bit
Pencil
Phillips Screwdriver
Tape Measure
Level
Part Supplied:
Shade Assembly
(2) Mounting Brackets
(2) Keeper Brackets,
(2)1/4-20x3/8" Phillips Screws
Crank Wand
(2) Bungee Cords
(4) Bungee Brackets
Crank Loop and Screw (4mmx20mm Machine Screw)
(6) #8x1-1/2" Flat-Head Phillips Screws
(4) #8x1-1/2" Round-Head Phillips Screws
CAUTION:
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY!
PLEASE READ THESE INSTRUCTIONS IN ITS ENTIRETY BEFORE ATTEMPTING TO COMPLETE
THIS PROCESS.
PLEASE NOTE THAT LEFT AND RIGHT REFERENCES ARE AS YOU FACE YOUR MOUNTING LOCATION.
The Sunsetter EasyShade can be installed with the mounting brackets on a wall (vertical surface) see Figure 1a or on the underside of a structure (horizontal surface) see Figure 1b. Each mounting bracket should be installed so that it is no more than 10" from the end of the shade.
 |
 |
STEP 1. Determine the desired location for the mounting brackets, making sure that they are plumb and level. Using a pencil, mark the 2 hole locations in the bracket. Using a 1/8" bit, drill holes approximately 1-1/2" deep at both hole locations. Repeat for the mounting bracket on the other side.
STEP 2A. For mounting on a wall (vertical surface), secure each bracket using two #8x1-1/2" round-head screws (see figure 1a)
STEP 2B. For mounting on an underside structure (horizontal surface), secure each bracket with one #8x1-1/2" round-head screw and one #8x1-1/2" flat-head screw. The flat-head screw is installed in the recessed area on the mounting bracket (see figure 1b). The round-head screw is installed in the flat area on the mounting bracket.
STEP 3. Secure the crank loop onto the gear shaft using the provided attachment screw.
STEP 4. Orient the shade assembly so that the crank loop is on your left as you face to installed brackets. With your helper, lift the shade assembly up to the installed mounting brackets (see figure 1a). Insert the front groove of the shade onto the protruding tab on the mounting brackets (see figure 1a). Press the shade assembly toward the top of the mounting bracket and insert the small keeper bracket into the rear groove of the shade near the installed bracket ( see figure 2). From the side, slide the keeper bracket into the opening between the mounting bracket and the shade (see figure 3).
STEP 5. Make sure that the slot in the small keeper bracket is aligned with the threaded hole in the mounting bracket. Secure them together using the supplied 1/4-20x3/8" Phillips screw. Repeat for the other side. Your installation is complete.
The
Sunsetter EasyShade extends down 6-1/2 feet to provide a wide range of
flexible shade. You may also choose to use the provided bungee and bungee
brackets so that the extended shade can be secured.
- Mount the bungee brackets at the desired height(s) using the screws provided
- Insert the bungee cord through the grommet at each corner of the shade
- Place the bungee cord over the hook on the bracket
NOTE: WE HAVE PROVIDED 2 SETS OF BUNGEE BRACKETS, WHICH GIVES YOU THE FLEXIBILITY TO HAVE PARTIAL AND FULLY EXTENDED FASTENING POINTS (see figure 4)
CAUTION: YOU SHOULD ROLL YOUR EASYSHADE UP WHEN THERE IS SEVERE WEATHER FORCASTED FOR YOUR AREA.